Let’s assume that you have a Cisco router with 2 ISP connection. The first one it’s a 10Mbps connection with a decent latency and the second one it’s a 2Mbps connection with quite high latency.

Since you don’t want to load balance over this 2 connections for the obvious reasons described above, you decide to to use the 10Mbps connection as the primary link and the 2Mbps one as a backup, just in case that the primary link fails.

You have no dynamic routing protocol, just a default route pointing to the primary link peer router. To understand better, please have a look to the topology below:

Of course, the easiest method would be to configure the a secondary default route through 2Mbps line but with a higher metric so it would be less preferred.  In this case when the main line goes done the backup default route comes into play. But what if the main line doesn’t go down? Just there is no reachability to Internet or some branch offices? This method will not work very well.

The solution that I propose is first to configure an IP SLA to monitor a certain destination (IP address) that you know if should always be UP. Like a server in your remote datacenter. In my example I will monitor the IP address 172.82.100.1 which is a server reachable over main provider:

ip sla 5
icmp-echo 172.82.100.1 source-interface GigabitEthernet0/0
timeout 1000
frequency 2
ip sla schedule 5 life forever start-time now

I believe you have an idea what IP SLA does. In this example it ping every 2 second the IP address 172.82.100.1 and it wait for reply (timeout) 1000ms before declare the host down.

Next we have to track this IP SLA for reachability:

track 1 ip sla 5 reachability

Pretty simple. I have a track number 1 which tracks IP SLA session 5 for reachability.

Now, most of the people (including I, in the beginning ) make a common mistake in setting the backup default route in the way that they set it based on the track 1:

ip route 0.0.0.0 0.0.0.0 10.10.10.1 track 1

This is not going to work. Why? Because track 1 check that the IP is reachable! When it is reachable, it will add the backup default route to the routing table and we will have 2 default routes: one through primary line and one through secondary (backup) lines. That’s bad because we need the backup route there only when the primary line fails to transport traffic to 172.82.100.1 in my example. We need somehow that this backup route to be applied when IP SLA 5 is NOT true. Here is is how:

track 2 list boolean and
object 1 not

In this track 2 we tell to track object 1 but to have the condition that this is not true. Now we can see the backup route:

ip route 0.0.0.0 0.0.0.0 10.10.10.1 track 2

and this will work correctly.

Small hint: You saw that in the IP SLA I’ve specified the interface from which I want to ping 172.82.100.1. This is not just a preferred method, but it’s mandatory! If you follow the steps above, when the backup default route will be in place, 172.82.100.1 will be reachable again, making the track 1 being true and setting the track 2 to think that the primary link is UP again, so it will retract the backup route through 10.10.10.1. Pinging with the source of the primary P2P link interface, you achieve the result that you want IP SLA 5 to be true only when pinging 172.82.100.1 through the first line. Remember that we are not using dynamic routing protocols.

In case  you didn’t catch this until now Gi0/0 is the 10Mbps link and the Serial0/0 is the 2 Mbps.

Another method to obtain the same result will be to used EEM with IP SLA which I will present in some future posts.

Cisco: Policy Routing with IP SLA
Tagged on:                                                                     

Leave a Reply

%d bloggers like this: